A Groundwork company - serving Irvine, CA

Toto Bathroom Remodeling in Irvine, CA

Bathroom remodelingBathroom remodeling
Kitchen remodelingKitchen remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Toto Bathroom Remodeling: The Irvine Owner’s Guide

Toto bathroom remodeling in Irvine typically costs $9,000 to $28,000, depending on scope, fixture tier, and whether we’re working around existing tile or rebuilding the wet zone from the studs. We install and service Toto-based bathroom projects across Irvine, and most planning visits get booked within a few business days. Groundwork Construction Co. of Irvine is an independent service provider – we’re not affiliated with Toto, and we’ll say so plainly when you ask.

Call (888) 578-4462

Owners in Irvine usually land on this page after the fixture they trusted starts to misbehave. The seat warmer on a Washlet quits mid-cycle. The bidet spray loses pressure and the nozzle stops extending. Water shows up at the base of a one-piece toilet and the floor tile near the flange feels soft. On a remodel scope, the tell is different: a Toto shower valve cartridge that’s been dripping for months finally etches a calcium ring into the trim, or a wall-hung toilet carrier that wasn’t blocked in correctly starts to flex. These problems show up in specific ways in Irvine because our water runs hard, and hard water is the single biggest killer of Toto rubber and ceramic internals in this city.

Which Toto Models This Applies To

Toto is organized by series, and the series dictates which replacement parts fit. The toilet lines most Irvine homeowners have are the Drake (CST743 and CST776, both elongated and round-front), the Ultramax II, the Aquia IV (wall-hung and floor-mount), the Neorest line of integrated smart toilets, and the Carlyle. The bidet seats are a separate world: the C5, C2, S7, S7A, and the higher-end S550e all use different washlet parts, and the C200/C100 entry line shares almost nothing with the S-series. Shower valves fall into the Toto Thermostatic and the older single-handle lines, and those two do not share cartridges.

The identification step is where most owners lose an afternoon. The model plate on a Toto toilet is under the tank lid on the inside left wall, not on the bowl or the base – and if someone has replaced the tank with an aftermarket unit at some point, the plate there won’t match the bowl. On a washlet, the model sticker sits on the underside of the seat near the hinge. Pull the seat, photograph the sticker, and write down the full model code including the suffix (a CST776CEFG#01 is not the same part as a CST776CEFG#51; the # code is the color, and mixing it up gets you a white lid on a cotton-white toilet).

On OEM versus aftermarket for Toto specifically: Toto’s own fill valves, flush valves, and washlet control boards are proprietary, and aftermarket “universal” fill valves that fit a Kohler or a Glacier Bay often won’t seat properly in a Toto G-Max or Tornado flush tower. For the fill and flush internals, we source OEM. For the supply line, the seat bolts, the wax ring, the angle stop, and the trim, quality aftermarket is fine and we’ll say so. Don’t mix the two categories up – the generic fill valve that “looks the same” is the single most common cause of a phantom running toilet we get called about in Irvine.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Toto Bathroom Remodeling Is Failing

  • The toilet runs for a few seconds every hour when nobody used it. The flapper or the fill valve seal is degrading, and the tank is slowly leaking into the bowl. In Irvine’s water, that seal hardens faster than the manufacturer’s number suggests.
  • The washlet seat warmer takes longer to heat, or shuts off on its own. The heating element or the control board is on the way out, and the S-series boards are not a cheap swap once they fail.
  • Bidet spray pressure drops or the nozzle stops extending. Mineral scale has packed the nozzle housing or the pump is losing prime. Hard-water Irvine homes see this most often on the city’s north side, where supply runs a touch harder.
  • Water or a wobble at the base of the toilet. The wax ring has failed or the flange is cracked, and if the floor feels soft you may be looking at subfloor damage rather than just a $30 ring.
  • The shower trim drips or the temperature swings. A Toto thermostatic cartridge that’s scaling up loses its mix and starts to drift – the “why is the shower suddenly cold” complaint usually traces back to a cartridge that needed replacing a year ago.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

For a Toto bathroom remodeling project in Irvine, our range runs $9,000 to $28,000. That covers everything from tile and waterproofing to fixture installation, the plumbing line work, and the finish. The lead drivers are tile choice, whether we open a wall for plumbing, and fixture tier – a Carlyle or a Neorest lands at the top of the range; a standard Drake with a mid-tier washlet sits nearer the bottom.

If the scope is narrower, these are the line items we quote separately, all installed:

Scope Installed Range (Irvine)
Bathroom remodel (full) $9,000 – $28,000
Small bathroom remodel $5,000 – $12,000
Walk-in shower installation $4,500 – $12,000
Tub-to-shower conversion $3,500 – $10,000
Shower replacement $3,000 – $8,500
Vanity installation $800 – $3,000

The price you see is the price you pay. We quote line by line, we hand you the written number before we start, and there are no change orders unless you ask for one mid-project. All work is backed by the 730-Day Done Right Promise – if it’s not done right, we make it right, and that covers the installation itself for two full years. We pull the permits Irvine requires for plumbing and structural work and we handle the inspections.

DIY or Call Us?

What you can safely do yourself: confirm the model number, photograph the underside of the washlet seat, shut off the supply valve before you touch anything, and check for a simple flapper seal. Those steps are harmless and save time on the call.

Where DIY goes sideways: on a Toto Neorest or a wall-hung Aquia, the tank-to-bowl gasket, the wall carrier, and the electrical components are not forgiving. A wall-hung toilet mounted to a carrier that wasn’t blocked properly in the wall can pull out of the frame if the hardware is over-torqued on a reinstall, and a washlet has a GFCI-protected circuit that can’t be handled by anyone but a licensed electrician. If you have a wall-hung or a Neorest, stop at the model sticker. We’d rather quote it than fix a pulled carrier.

For the standard pedestal toilets and valve cartridges in an Irvine home, you can call us at (888) 578-4462 and we’ll walk you through whether it’s a parts job or a real scope. A live person answers 24/7, no voicemail, and a free estimate books into your week.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 578-4462
Local Service Coverage

Request a Free Estimate in Irvine

Tell us what you need - Groundwork Construction Co. of Irvine responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch