Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
PGT Fence Installation: The Irvine Owner’s Guide
PGT fence installation in Irvine typically runs $3,500 to $9,000 installed, depending on gate count, height, and how much site prep the yard needs. We install and repair PGT-compatible fence systems for Irvine homeowners and can usually get a failed gate, post, or latch section back in working order in a single visit. Most owners only discover something’s wrong when a gate starts dragging on the ground, a latch stops catching, or a post shifts after a wet winter and the whole run starts to lean.
PGT is best known for windows and doors, and that’s worth stating plainly up front: we’re an independent service provider, not affiliated with PGT. But we work on PGT-branded and PGT-compatible exterior products often enough to know the specs, the common failure points, and where a homeowner can get talked into the wrong replacement part. If your fence hardware or gate assembly carries a PGT label or came with a PGT-spec package, this page is for you.
Which PGT Models This Applies To
PGT exterior products are tied to model and series numbers, and the part you need is tied to that number in turn. The label is typically on the gate frame, the hinge plate, or the post bracket. If the label is weathered off, measure the hardware footprint instead: hinge spacing, post width, and gate frame thickness are the three numbers that will match you to the right assembly.
Here’s the compatibility gotcha most Irvine homeowners miss. PGT fence and gate hardware is often matched to a specific frame thickness and latch throw depth, and a generic hardware set from a big-box store will usually bolt on but won’t align properly. You’ll get a gate that closes but doesn’t latch flush, or a hinge that wears out in a season because the load isn’t distributed the way the PGT frame was designed for.
OEM or aftermarket for a PGT system?
For gate hardware, latches, and hinges, we favor OEM or true OEM-equivalent parts when they’re available, because the dimensional tolerances matter more than most homeowners realize. For panels, posts, and rails, a quality aftermarket equivalent is often the smarter spend, especially on a fence that’s already north of ten years old. We’ll tell you which is which before you commit to anything, and our pricing is upfront with no surprises.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your PGT Fence Installation Is Failing
- Gate dragging on the ground or scraping the driveway. Usually a sagging hinge or a post that’s settled on one side. Irvine’s expansive clay soils shift seasonally, and a post set without proper depth or base material will move within a few years.
- Latch not catching or popping open on its own. The latch throw has worn past the strike plate tolerance. This is a security issue, not just an annoyance, and it’s usually a small part swap rather than a full gate replacement.
- Loose or wobbly posts after rain. Water pooling at the post base rots the footing or undermines the concrete collar. If a post moves by hand, the footing needs attention before the panels above it fail.
- Rust streaks or white corrosion on hardware. Salt air and coastal humidity work on cheap fasteners faster than most people expect. Visible corrosion on hinges or brackets means the hardware is past its service life, even if the panels look fine.
- Panels leaning out of plumb. A run that was square last year and leans this year is telling you the soil or the footings are the problem. Catching this early saves the panel replacement that follows.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Irvine, expect $3,500 to $9,000 for a full vinyl fence installation, and $4,000 to $10,000 for aluminum. Hardware-only repairs (a hinge set, a latch assembly, a single post reset) land well below that and we’ll quote them separately so you’re not paying for a full install when a part swap will do. The range is driven by linear footage, gate count, height, material choice, and site prep – a yard with root intrusion or a failed existing footing costs more to set right than a clean run.
What’s included in the quote
- Written line-item quote with parts and labor separated
- Removal and haul-away of the failed section or hardware
- Post footing repair where needed
- Cleanup and a final walkthrough before we call it done
Every fence project we complete is covered by our 730-Day Done Right Promise. If it’s not done right, we make it right. We also offer 0% financing for 18 months and $1,000 off projects over $10,000, so a larger run or a full replacement doesn’t have to come out of savings in one hit.
DIY or Call Us?
Some of this you can safely check yourself. Walk the fence line and look for movement at the post base, test the latch by hand, and look for rust or corrosion on the hardware. Those are five-minute checks that tell you whether you’re looking at a part swap or a footing problem.
Where DIY goes wrong is at the footing and the gate frame. Digging out and re-setting a post without knowing the soil conditions or the correct base depth is how a one-weekend job turns into a leaning run by the next rainy season. Adjusting a gate hinge on a PGT frame without matching the load spec is how you get a gate that latches for three months and then doesn’t. And if the hardware is load-bearing or the post is structural, a bad DIY fix can turn a safe gate into one that swings open onto the driveway. Call us at (888) 578-4462 and we’ll tell you honestly whether it’s a part swap or a bigger job.
FAQs
A well-installed vinyl fence in Irvine typically lasts 20 to 30 years, and aluminum runs 30-plus, but the hardware (hinges, latches, brackets) usually needs attention at the 8 to 12 year mark. Irvine’s seasonal soil movement is the biggest factor in how long the footings hold. Call (888) 578-4462 for an exact quote – estimates are free.
Yes, in most cases. A single failed hinge, latch, or post is a repair, not a replacement, and we quote it that way. Full replacement only makes sense when the panels themselves are failing across the run or the footings have failed in multiple spots. Call (888) 578-4462 and we’ll tell you which category you’re in.
Hardware-only repairs are usually done in a single visit, often within a couple of hours. A single post reset or section replacement typically takes half a day. A full run replacement runs one to three days depending on footage and gate count. Call (888) 578-4462 to schedule your free estimate and we’ll give you a specific timeline.
We source OEM or OEM-equivalent parts by model number when the label is legible, and by measured footprint when it isn’t. We don’t claim to stock parts locally or carry them on a truck; we order to spec and confirm the match before installation. Call (888) 578-4462 to get the right part ordered for your system.
We also work with KraftMaid, Cambria, and Silestone on the interior side, so if a fence project turns into a bigger exterior-and-interior scope, you’re working with one contractor from foundation to finish line. Our technicians have up to 12 years of experience, are background-checked, and arrive in uniform on every job.
Fence problems in Irvine don’t fix themselves, and a gate that won’t latch is a security risk, not just an inconvenience. Call Groundwork Construction Co. of Irvine at (888) 578-4462 to schedule your free estimate. A live person answers 24/7, so you won’t hit voicemail no matter when you call.
Written by the team at Groundwork Construction Co. of Irvine, serving Irvine and nearby areas.