Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ES Windows Kitchen Remodeling: The Irvine Owner’s Guide
Kitchen remodeling built around ES Windows products in Irvine typically runs $14,000 to $45,000 installed, depending on cabinet scope, countertop material, and whether windows or a slider are part of the layout. Most projects are planned and scheduled, not rushed; we walk every Irvine home before quoting so the number holds.
Owners usually land here after a specific failure. A cabinet run that no longer lines up under a window. A slider that sticks when the afternoon heat hits. A countertop seam that’s lifted near a glass door. In Irvine’s dry inland climate, the parts that age first are the ones exposed to sun and temperature swing: window seals, glazing gaskets, and the trim and filler pieces that tie ES Windows openings into new cabinetry. Once you can name the failing part, matching it to your ES Windows model is the whole job. Groundwork Construction Co. of Irvine is an independent contractor and is not affiliated with ES Windows.
Key Takeaways
- Installed kitchen remodeling in Irvine: $14,000 to $45,000 for full scope, $9,000 to $20,000 for a small kitchen.
- ES Windows parts are matched by series and by measured opening, not by eyeballing a photo.
- Window-to-cabinet fit is the most common reason an ES Windows kitchen remodel needs a custom filler piece.
- We quote upfront pricing in writing, and the work is backed by our 730-Day Done Right Promise.
Which ES Windows Models This Applies To
ES Windows is a Southern California manufacturer, so the parts we source most often for Irvine kitchens are the ones tied to their vinyl and aluminum series used in residential remodels: sliding glass doors that open to a patio, fixed and casement windows over a sink, and the fascia and trim kits that finish those openings. If your kitchen window or slider carries an ES Windows label on the frame or the glass spacer, you can usually read the series designation there. If the label is painted over or gone, we measure the rough opening and the visible glass area rather than guess.
That measurement step matters. ES Windows parts are sized to the specific series and to the opening the builder framed, and a part from a neighboring series will fit loosely, bind, or leave a gap you can see daylight through. For kitchen work, the critical measurements are the rough opening width and height, the frame depth, and the glass-to-frame offset. Bring those three numbers into a conversation and a correct part can be matched without a second visit.
The OEM-versus-aftermarket call is real. On visible pieces like interior trim and filler strips, a quality aftermarket match is often indistinguishable and costs less. On anything structural to the window or door itself, glazing, seals, sliding hardware, we push for the OEM-equivalent part because the tolerances are tight and a near-fit fails faster in Irvine’s summer heat. When we quote, we show you which side of that line each line item falls on.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your ES Windows Kitchen Remodeling Is Failing
- Sticking or dragging slider. The rollers or track have worn or collected grit, and the door no longer glides square. Left alone, the misalignment chews the seal and lets air in.
- Condensation between panes or fogging. The seal on a dual-pane unit has failed and moisture is trapped in the gap. That’s a glass-unit replacement, not a cleaning job.
- Drafts at the frame or sill. The weatherstripping or perimeter seal has compressed or cracked, usually on the sunny side of the house where UV hits hardest.
- Gaps where cabinetry meets the window or slider. The filler or trim piece has shrunk, warped, or was never fitted to the opening. This is the classic ES Windows kitchen fit problem in Irvine.
- Visible rot or softness at the sill or jamb. Moisture has been getting behind the frame. This one needs to be opened up and inspected before you finish over it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Irvine kitchens, here’s the honest range. Full kitchen remodeling runs $14,000 to $45,000; a small kitchen remodel lands at $9,000 to $20,000. By line item:
- Cabinet installation: $4,000 to $13,000
- Countertop installation: $2,000 to $6,500
- Kitchen island installation: $3,000 to $10,000
- Backsplash installation: $800 to $2,500
What drives the range: cabinet line and count, whether the layout moves, countertop material (Cambria and Silestone sit in different brackets than builder-grade quartz), and whether ES Windows openings need re-trimming or a window/door part swapped. Parts and labor are shown as separate lines so you can see exactly what the part costs and what the install costs. Every job carries the 730-Day Done Right Promise, in writing. Upfront pricing, no surprises: the number you approve is the number you pay.
DIY or Call Us?
You can safely measure your ES Windows opening, photograph the frame label, and check whether the slider or sash moves square. That’s useful info and we’ll use it. Where DIY goes wrong: forcing a misaligned slider or prying trim around a sealed frame can crack glazing, break the seal, and turn a part swap into a full unit replacement. Any cutting near glass, and any work that touches the window frame itself, belongs with someone trained for it. Our technicians with up to 12 years of experience handle the fit and finish. Call (888) 578-4462 to schedule your free estimate.
FAQs
Visible trim and filler pieces hold up for years if the seal behind them stays intact, but seals and weatherstripping on sun-exposed windows and sliders in Irvine often show wear within a decade of daily exposure. The part isn’t the problem; the UV and temperature swing are. Call (888) 578-4462 for a free inspection.
Sometimes. A sticking slider is often a roller or track service, and a worn perimeter seal can be re-sealed. Fogged glass units, cracked frames, and soft sills get replaced. We’ll tell you which one you’re looking at before anyone orders parts.
A single part or trim exchange is usually done in one visit; a full kitchen remodel with ES Windows fit work runs weeks, not days. We schedule around your kitchen being usable and tell you the timeline in writing. Call (888) 578-4462 to get your project on the schedule.
By series designation and measured opening, then sourced from the correct manufacturer channel, never guessed from a photo. We confirm the part before install so it fits the first time. Call (888) 578-4462 to start.
We also work with KraftMaid, Cambria, and Silestone on Irvine kitchen projects, so the cabinets and counters around your ES Windows openings are matched to the same standard as the windows themselves. From foundation to finish line, one contractor, upfront pricing, and a 730-Day Done Right Promise behind every job. Calls are answered by a live person 24/7. Call (888) 578-4462 to schedule your free estimate and design consult.
Written by the team at Groundwork Construction Co. of Irvine, serving Irvine and nearby areas.