Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ECO Window Systems Bathroom Remodeling: The Irvine Owner’s Guide
Bathroom remodeling built around ECO Window Systems products in Irvine typically runs $9,000 – $28,000 installed, depending on whether it’s a cosmetic refresh or a full gut with a walk-in shower conversion. We’re an independent contractor and not affiliated with ECO Window Systems, but we source, fit, and install ECO Window Systems shower doors, frameless glass panels, and window units every month in Irvine homes. Most owners don’t discover a failing component until a shower door drags or won’t latch, water starts weeping past a seal, or a window over the tub fogs from the inside. By then the part has usually been warning you for months.
Key Takeaways
- ECO Window Systems bath components in Irvine typically fail at the seals, hinges, and rolling hardware before the glass does.
- Installed bathroom remodel pricing in Irvine: $9,000 – $28,000. Small bathroom remodel: $5,000 – $12,000.
- OEM and quality aftermarket replacements both exist. Match by series, not by look.
- We don’t stock parts or carry them on a truck. We measure, source, and schedule the install.
- Every job is covered by our 730-Day Done Right Promise.
Which ECO Window Systems Models This Applies To
ECO Window Systems bathroom products span a few families: framed and semi-frameless shower enclosures, frameless glass doors, pivot and sliding shower doors, and the company’s window lines used in bath and powder rooms. The part you need is tied to the series, not the room. Two enclosures can look identical and use completely different hinge geometry, glass thickness, and seal profiles, so we always start with the ID sticker on the frame or on the glass edge.
Look for the manufacturer label on the top or side of the door frame, on the glass edge, and inside the track on sliding units. If the sticker is gone, we measure: glass thickness in millimeters (8mm and 10mm are the two common frameless specs), panel width and height to the nearest millimeter, hinge hole spacing center-to-center, and pivot hardware diameter. Written down, those numbers tell us exactly which ECO Window Systems series you’re dealing with.
Now the OEM-versus-aftermarket call. OEM hardware is the safest match when the frame is intact and you’re replacing a hinge, roller, or seal. Quality aftermarket equivalents are often the better buy when the original part is discontinued or when the OEM piece is a known weak point. The catch specific to ECO Window Systems is that some of its frameless lines sold through West Coast dealers were built in short production runs, so a discontinued hinge can force you onto an aftermarket set. On a Spanish-style Irvine home with a glass enclosure exposed to hard afternoon sun, the rubber seals dry out faster than on shaded installs, so seal sourcing matters as much as hardware sourcing.
We also service KraftMaid, Cambria, and Silestone components if your Irvine bath remodel touches vanity or countertop surfaces at the same time.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your ECO Window Systems Bathroom Remodeling Is Failing
- Shower door drags or won’t close flush. The bottom pivot or roller has worn, or the hinge screws have loosened into the frame. Left alone, the glass can torque and chip at the hinge point.
- Water on the floor outside the enclosure. The door sweep or magnetic seal has hardened or torn. In an Irvine bath with direct sun on the glass, rubber seals age quickly from UV exposure.
- Cloudy glass or mineral film behind the panel. Hard water in Irvine leaves calcium deposits that etch the glass surface. Once it’s etched, polishing won’t fully clear it; replacement is the honest fix.
- Fog between the panes on a bath window. The insulated glass unit’s seal has failed and moisture has gotten into the gap. This can’t be repaired on the unit, only replaced.
- Loose or rusting frame hardware. Salt air and bath humidity attack the finish on hinges and handles. Rust streaks at the hinge tell you the hardware is past its service life.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in Irvine for the work that surrounds these parts:
| Project | Installed Range |
|---|---|
| Bathroom Remodel (full) | $9,000 – $28,000 |
| Small Bathroom Remodel | $5,000 – $12,000 |
| Walk-In Shower Installation | $4,500 – $12,000 |
| Tub-to-Shower Conversion | $3,500 – $10,000 |
| Shower Replacement | $3,000 – $8,500 |
| Bathroom Vanity Installation | $800 – $3,000 |
What moves the number: glass thickness, door configuration, whether the enclosure is frameless or framed, wall condition behind the existing unit, and whether plumbing has to move. Our quotes are line-item and upfront, the number you see is the number you pay, and the work is covered by the 730-Day Done Right Promise. No change-order games mid-job.
DIY or Call Us?
Here’s the honest split. You can safely check the ID sticker, measure panel width and height, note glass thickness, photograph the hinge and hardware, and write down the model. That information makes the whole job faster.
What we’d steer you away from is lifting and refitting a frameless glass panel yourself. Tempered glass in a shower enclosure can weigh well over 100 pounds, and the failure mode is not a crack; it’s a full shatter with sharp pieces coming down around your feet and hands. Wall anchors for a heavy panel also have to hit studs or proper blocking, and on Irvine homes that means verifying what’s actually behind the tile before you drill. That’s not a weekend job.
Call us at (888) 578-4462 and we’ll set a free estimate. With an experienced trade background behind every crew and background-checked technicians on every project, we handle the measurement, sourcing, and install in one visit whenever possible.
FAQs
How long do ECO Window Systems shower doors and bath windows last in Irvine? Frameless shower hardware typically gives you 8 to 12 years before hinges or rollers need replacing, and rubber seals often need attention sooner, around 5 to 7 years in sunny Irvine bathrooms. Bath windows with insulated glass usually last 15 to 20 years before the seal fails. Call (888) 578-4462 for an exact quote on a replacement.
Can the part be repaired instead of replaced? Often yes. A worn hinge, roller, or door sweep can be swapped without touching the glass, which is the least expensive path when the panel is in good shape. If the glass itself is etched, chipped, or fogged, repair isn’t realistic and replacement is the right call. Call (888) 578-4462 and we’ll tell you which side of that line you’re on.
How long does the swap take? A hardware or seal replacement on a shower enclosure usually finishes in a couple of hours. A full shower replacement or a window unit swap generally runs a half day to a full day depending on wall condition. Larger bathroom remodels of the type in the pricing table take considerably longer. Call (888) 578-4462 to schedule your free estimate.
How do you source the part? We start with the model ID and exact measurements, then match against current ECO Window Systems parts or a quality aftermarket equivalent. We don’t stock parts and don’t carry them on a truck so lead time varies. If a discontinued part forces an aftermarket match, we tell you upfront before you commit. Call (888) 578-4462 and we’ll walk you through options.
Call (888) 578-4462 for a free estimate on your ECO Window Systems bathroom project in Irvine. Live person, 24/7. Upfront pricing, no surprises. Every job backed by the 730-Day Done Right Promise.
Written by the team at Groundwork Construction Co. of Irvine, serving Irvine and nearby areas.