Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Quikrete Home Additions & ADU: The Irvine Owner’s Guide
We build Quikrete-ready home additions and ADUs in Irvine, and a typical project runs $45,000 – $130,000 installed, depending on square footage, foundation work, and finish level. Quikrete isn’t a manufacturer of structural systems, so what owners usually land with is the concrete side of the job: Quikrete anchoring epoxy, concrete mix, or repair mortar that’s failed, cured wrong, or been sitting half-used in the garage since a previous project. You find out the hard way when a post base pulls loose, a slab patch crumbles, an anchor won’t hold torque, or a new footing lifts after one wet Irvine winter. That’s the moment the search starts.
Key Takeaways
- Concrete and anchoring products fail most often because of water ratio, cold joints, and improper surface prep, not because of the brand.
- Irvine’s clay-rich soils expand and contract seasonally, which is hard on slab edges, post bases, and shallow footings.
- Most concrete-related part failures we see are fixable without redoing the whole addition.
- Groundwork Construction Co. of Irvine is an independent service provider, not affiliated with Quikrete.
Which Quikrete Models This Applies To
Quikrete doesn’t use “model numbers” the way a garage door opener or appliance does. Products are identified by product line and product number printed on the bag, bucket, or tube, and that’s what you’ll match against. Common ones in an addition or ADU setting include High Strength Concrete Mix (the 80 lb bag), Fast-Setting Concrete, Anchoring Epoxy (sold in dual-cartridge systems), and Vinyl Concrete Patcher for slab edge repairs. If you’re holding an old bag, read the number under the Quikrete logo, not the marketing banner, and note the bag weight – the 60 lb and 80 lb versions of the same mix use different water volumes and are not interchangeable in a mixer by eye.
The OEM-versus-aftermarket question is worth answering honestly. For Quikrete-branded anchoring epoxy, the OEM cartridge and mixing nozzle matter because the two-part ratio is set by the manufacturer; a generic nozzle that doesn’t match the cartridge can leave unmixed resin that never fully cures. For concrete mix, we use Quikrete where it’s the right spec and an equivalent when a regional supplier has fresher stock, because bagged concrete has a real shelf life – roughly six months stored dry, and much less in a garage that sees Irvine’s summer heat. Freshness beats brand on this one. For the visible finish side of an addition, our material partnerships run through KraftMaid, Cambria, and Silestone; Quikrete handles the structural and repair chemistry underneath.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Quikrete Home Additions & ADU Is Failing
- A post base or anchor pulls out under load. Usually anchoring epoxy that was mixed cold, set in a damp hole, or drilled without blowing dust out first. Resin can’t bond to dust.
- Patch mortar crumbles along a slab edge within a season. Thin feather-edge patches without a bonding agent will fail every time, and Irvine’s dry summers plus winter rain cycles accelerate it.
- A footing or slab lifts or cracks at a seam. Clay soils under Irvine shift as they wet and dry, which is why a cold joint poured without dowels or reinforcement opens up.
- Concrete poured from an old bag never hardens, or sets chalky. Bagged mix absorbs moisture from the air over time; if the bag was stored in a garage, the cement is already partially hydrated.
- Anchors won’t hold torque after curing. Almost always a hole drilled too large, drilled oversize to chase a wandering bit, or not cleaned with a brush and air before resin went in.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Concrete-related repairs tied to an addition or ADU in Irvine land in our $45,000 – $130,000 project range when they come bundled with structural work. A stand-alone repair is far less, and we quote it line by line so you can see the split.
| Scope | Typical Installed Range | What’s Included |
|---|---|---|
| Isolated anchor or post base reset | $350 – $900 | Old resin removed, hole re-drilled and cleaned, fresh anchoring resin, hardware re-torqued |
| Slab edge or patch repair | $800 – $2,500 | Failed patch ground out, bonding agent, fresh patcher, joint sealing |
| Footing or pier reinforcement | $3,000 – $9,000 | Excavation, dowels, new concrete, inspection coordination |
| Full addition or ADU build | $45,000 – $130,000 | Permits, foundation, framing, concrete, and finishes |
What pushes a quote toward the top of the range: site access for a mixer, whether the existing slab has to come out, and Irvine permit and inspection fees. We pull the permits and pass the inspections. Our workmanship is covered by the 730-Day Done Right Promise, and pricing is upfront – the number you see is the number you pay.
DIY or Call Us?
There’s a safe middle ground here. Checking the product number and bag weight on an old Quikrete bag, reading a label, taking a photo of a cracked patch, and testing whether an anchor is loose by hand are all fine. If you’re considering a small anchoring job, know that the resin itself won’t hurt you, but an anchor that lets go under load can – a post base that fails while holding up a beam is not the moment you want to discover the hole was drilled wrong. Chasing a footing, cutting out a slab seam, and removing cured anchoring epoxy are where homeowner efforts typically go sideways. Our technicians have up to 12 years of experience and the right equipment to drill, clean, and cure this properly. Calls are answered by a live person, 24/7. Call (888) 578-4462 for a free estimate.
FAQs
Properly mixed anchoring epoxy in a clean, dry hole typically holds for the life of the structure, and a concrete mix cured at the right water ratio does the same. The common failure is not the product – it’s prep and curing. Irvine’s dry air pulls moisture out of a fresh pour fast, so early curing matters. Call (888) 578-4462 and we’ll look at what you’ve got and tell you straight.
Yes, in most cases. A failed pad or slab patch can be ground out and repoured with a bonding agent and fresh material, and a loose anchor can usually be re-drilled and reset. Full replacement is only needed when the underlying concrete is compromised. Call (888) 578-4462 to schedule a free estimate.
Most isolated repairs are finished in a single visit, though anchoring resin needs time to fully cure before you load it. Footing or pier work takes longer because of excavation and inspection. We’ll give you a clear schedule before we start. Call (888) 578-4462 for a specific timeline.
We source directly from regional suppliers for freshness, not from any back-stock, and match the product number and spec to the job at hand. We don’t carry Quikrete parts or bags in inventory – every job is sourced when it’s scheduled. Call (888) 578-4462 and we’ll walk through the right product for your repair.
Written by the team at Groundwork Construction Co. of Irvine, serving Irvine and nearby areas.