Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in Irvine: What It Takes and What It Costs
Door installation in Irvine runs $450 to $1,400 per interior door and $900 to $3,200 for most exterior or patio entries, depending on material, frame condition, and whether hardware and trim are included. A single pre-hung swap is usually a one-day job; a whole-house interior package or a wall opening that needs a new header takes three to five days. Call (888) 578-4462 for a free on-site estimate and a written line-item quote before anyone touches a jamb.
How Groundwork Handles Door Installation From Measure to Final Swing
Doors fail in predictable ways, and the fix starts before the saw comes out. Here’s the sequence we run on every Irvine door job, with the points where you make the call.
Stage 1: On-site measure and swing check (day 1, about 60 to 90 minutes)
We measure the rough opening, check the jamb for plumb and square, and confirm the swing direction and clearances. You decide door style, slab or pre-hung, and whether existing casing and baseboard stay. This is also when we spot the surprises that change scope, like a frame that’s out of square or a wall that isn’t where the original plans say.
Stage 2: Written quote and material selection (24 to 48 hours later)
You get a line-item quote covering the door, frame prep, hardware, trim, and any drywall repair. Material decisions lock in here, which matters: a solid-core interior door and a hollow-core one look similar on a sample board and behave very differently over ten years. We put the numbers in writing so the finished price matches the quoted one.
Stage 3: Demo and opening prep (day 2, half a day)
Out comes the old door, casing, and any damaged jamb. We square up the rough opening, repair rotted framing or water-damaged sill material, and confirm the header carries the load if we’re enlarging an opening. Anything structural gets flagged and re-quoted before we continue, never after.
Stage 4: Hang, shim, and seal (day 2 into day 3)
We set the unit, shim the hinge and strike sides, check the reveal gap all the way around, and adjust the strike plate until it latches with a light push. Exterior doors get flashing, sill pan, and a continuous sealant bead. Hardware goes on last so scratches get touched up rather than covered up.
Stage 5: Finish and walkthrough (day 3 to day 5 for trim, paint, and punch)
Casing and baseboard return, nail holes fill, and paint or stain goes on per your finish plan. Then we walk it with you: latch, lock, sweep, and weatherstrip all tested in front of you. Most single-door jobs finish inside one visit; trim and paint across a whole house typically add two to three days.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Real Choices You’ll Make on an Irvine Door Installation
Most of the money and most of the regret live in these decisions. Here’s the honest trade-off on each.
- Hollow-core vs. solid-core interior doors: Hollow-core is the cheaper route, roughly $120 to $300 per slab installed, and it’s fine for closets. Solid-core costs more and kills sound transfer between rooms; worth it in bedrooms and home offices where a door gets used all day.
- Pre-hung vs. slab: Pre-hung units come with the frame and hang faster, which saves labor. Slab replacement keeps the original frame and makes sense only when the jamb is still square and solid.
- Exterior material: Fiberglass and steel hold up to Irvine’s dry heat and UV load better than wood, which needs refinishing every few years. Wood is the choice when you’re matching a Spanish-revival entry and the look outweighs the upkeep.
- Glass and glazing: A patio or entry door with tempered glass runs higher, but it’s code-required in many locations and brings in daylight. Frosted or reeded glass solves privacy on street-facing entries.
- Hardware and finish: Builder-grade knobs and hinges wear out first. Oil-rubbed bronze, matte black, and satin nickel hold up; cheap finishes pit within a couple of years. Lever handles beat knobs for aging-in-place plans.
- Prehung brand and grade: Name-brand units from Andersen and Pella cost more upfront and typically hold their alignment longer than no-name imports. On a full exterior package, that difference shows up as fewer adjustment calls down the road.
What Door Installation Costs in Irvine, CA
Expect $450 to $1,400 per interior door installed, $900 to $3,200 for a standard exterior or patio door, and $2,000 to $5,500 when an opening has to be resized or a new header framed. Those ranges hold steady across Irvine because labor rates are consistent within the village HOAs; what moves the number is scope, not address.
- Door grade and material: A hollow-core interior slab and a fiberglass exterior unit are not in the same price league. Material is usually the single biggest line item.
- Existing frame condition: A sound, square jamb keeps the job simple. Rotted sill material, out-of-square framing, or water damage behind an exterior door adds repair time.
- Opening changes: Enlarging or relocating a doorway means framing and a new header. This is where jobs jump, and also where permits may come in.
- Hardware and finish level: Standard knobs and hinges are budget; high-end levers, multi-point locks, and premium finishes push the top of the range.
- Trim, paint, and drywall: Turning a bare opening back into a finished wall takes carpentry, patching, and painting, and it’s priced accordingly.
A written estimate from us covers the door, hardware, frame prep, trim, cleanup, and haul-away, plus a permit if the scope needs one. It typically does not cover structural changes discovered mid-job, custom or special-order doors with lead times, or matching existing stain the way a specialized refinisher would. Upfront pricing means the number you see is the number you pay unless you approve a change.
See the difference
Before
After
Before
After
Before
AfterWhat Irvine Homes Specifically Do to a Door Installation
Irvine was built almost entirely by the Irvine Company from the 1960s forward, which means most door work here happens inside a village HOA with its own design-review board and architectural standards, not in a patchwork of independent jurisdictions. Before we hang an exterior door on a Woodbridge or Northwood tract home, we confirm the village association’s approved color and door style, because a nonconforming replacement can trigger a correction notice. Out along Irvine’s eastern and southern edges near the open space and the Santa Ana foothills, WUI fire-hardening requirements apply, and exterior doors there need to meet ember and noncombustible standards that contractors from Santa Ana or Tustin routinely miss on their first Irvine plan check.
The stock we see most is 30- to 50-year-old stucco tract housing and townhomes with builder-grade doors that have sagged, swollen at the sill, or lost their weather seal in the dry heat. Turtle Rock and the UCI-area condos run older too, and the patio doors there often need full sill-pan replacement, not just a new slab. Interior doors in these homes tend to be hollow-core builder grade, which is exactly what’s worth upgrading. If the work is part of a full Windows & Doors in Irvine scope, we sequence the door openings with the glazing so the whole envelope gets sealed once, and homeowners often pair this with Chain Link Fence in Irvine or Vinyl Fence in Irvine when the yard is getting reworked at the same time. You can see the full range of our Windows & Doors work, and we cover all of Irvine village by village.
Serving Irvine, CA – Our Local Coverage Area
We serve Irvine and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Door Installation in Irvine
A single pre-hung door takes about a day, while a whole-house interior package or a resized opening runs three to five days once trim and paint are included. Schedule time separately for special-order doors and their lead times. Call (888) 578-4462 for a realistic timeline on your scope, and the estimate is free.
Like-for-like replacement in an existing opening usually doesn’t need a permit, but resizing an opening, cutting a new header, or adding an exterior door to an exterior wall generally does, and Irvine’s building division reviews those closely. We pull the permits and pass the inspection for you. Call (888) 578-4462 and we’ll confirm what your specific job requires.
Yes, in most cases a standard replacement stays inside the existing opening and leaves plumbing and framing untouched. Only when we’re widening a doorway or relocating an opening does framing come into play. We flag that after the measure, before any work starts. Call (888) 578-4462 to book your free estimate.
Interior doors run about $450 to $1,400 each installed, exterior and patio doors $900 to $3,200, and resized openings $2,000 to $5,500. Your written line-item quote comes from the on-site measure, and there are no change orders unless you approve them. Call (888) 578-4462 for an exact number.
Every door installation we do is covered by our 730-Day Done Right Promise; if it isn’t done right, we make it right. Manufacturer warranties on doors and hardware stack on top of ours. Call (888) 578-4462 to talk through coverage for your job.
Get Your Free Door Installation Estimate in Irvine
Call (888) 578-4462 and a live person answers, day or night, to book a free on-site estimate for your door installation in Irvine. We measure, quote line by line, and explain any permit or HOA step before you commit. Projects over $10,000 get $1,000 off, and 0% financing for 18 months is available. Built to last, backed in writing.
Written by the team at Groundwork Construction Co.