Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Kitchen Remodeling: The Irvine Owner’s Guide
CGI-compatible kitchen remodeling in Irvine typically runs $14,000 to $45,000 installed for a full kitchen, with cabinet-only work landing between $4,000 and $13,000. Most Irvine homeowners call us after a cabinet door stops closing flush, a drawer glides crooked, or a countertop seam starts catching a fingernail – the three failure points we see most in CGI kitchens across Irvine. That first sign usually shows up years after the original install, when a hinge plate has loosened in the particleboard or a laminate edge has lifted near the sink run.
Key Takeaways
- Full CGI kitchen remodels in Irvine: $14,000 – $45,000 installed.
- Cabinet-only swaps: $4,000 – $13,000; countertops alone: $2,000 – $6,500.
- Groundwork Construction Co. of Irvine is an independent contractor, not affiliated with CGI.
- Every job is backed by the 730-Day Done Right Promise.
- Call (888) 578-4462 for a free estimate and design consult.
Which CGI Models This Applies To
CGI cabinetry shows up across a wide range of series, and the part that fits one factory run won’t fit the next. Before we can match a replacement door, drawer box, glide, or hinge, we confirm the model line from the label inside the cabinet carcass – usually tucked on the back of a door or the inside wall of a base cabinet. If a label is gone, we measure the door overlay and the drawer front opening, since CGI has used several overlay standards over the years and getting that number wrong means a new door that sits proud or short.
On the countertop side, the CGI name shows up mostly on laminate and solid-surface tops. Cracks and delamination are the failures that push people toward replacement rather than repair. We compare an OEM-match laminate against a Cambria or Silestone quartz upgrade, since CGI’s top is often the cheapest piece of the kitchen to change and upgrading it changes the whole room.
The OEM-versus-aftermarket call is simple on hardware and less so on doors. A quality aftermarket hinge or glide from a known brand will outlast the OEM part in most cases and cost less. A door face, though, has to match the finish and profile of the run it sits in, so that’s where sticking with a CGI-compatible replacement makes more sense. We also install KraftMaid and Cambria cabinetry if a full re-face is the better route than chasing individual parts.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Kitchen Remodeling Is Failing
- Doors that won’t stay closed or drag on the frame. A loosened hinge plate in the particleboard carcass has stripped its screw holes. This is the most common CGI cabinet failure we see in Irvine homes built in the 2000s.
- Drawers that wobble or jam halfway out. The glide has worn past its tolerance or the side-mount bracket has pulled free. Once a drawer box flexes, the glide can’t hold square.
- Lifted edges or bubbling along the laminate. Moisture has crept under the top near the sink or dishwasher. Irvine’s dry air hides the problem until a wet season drives the failure visibly upward.
- Seams that catch a fingernail or show a dark line. The seam adhesive has given up, and water now gets behind the joint. Left alone, the substrate underneath swells and the top has to come off.
- A cabinet face that peels or delaminates at the edge band. Heat near the range and everyday wiping wear the edge band over time. Once the band lifts, the particleboard core is exposed and swells fast.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what CGI-compatible kitchen work runs in Irvine. These are installed prices, parts and labor together, with an upfront written quote so the number you see is the number you pay.
| Scope | Installed Price in Irvine |
|---|---|
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation / replacement | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What pushes a job toward the top of a range: the number of cabinets, a full re-face versus a hardware swap, quartz versus laminate, and whether plumbing or electrical has to move. Most cabinet-only swaps finish in a single visit. Every project carries the 730-Day Done Right Promise, so if something isn’t right after install, we make it right.
DIY or Call Us?
You can safely check a few things yourself. Confirm the model label on the cabinet, measure the door overlay and drawer opening, and note whether the failure is hardware, door, or top. Adjusting a hinge with a screwdriver is fine if the plate is intact and just out of alignment.
Where DIY goes wrong is chasing a stripped hinge in particleboard with a bigger screw, or trying to re-glue a lifted laminate edge that has already let water in. Both fixes hold for a few weeks and then fail worse. Electrical and plumbing behind a cabinet or under a sink are jobs for a trained professional, not a weekend project. If the failure involves anything behind a wall or under the counter, call (888) 578-4462 and we’ll tell you honestly whether it’s a repair or a replacement.
FAQs
How long does a CGI kitchen last in Irvine? A CGI kitchen typically holds up 15 to 20 years in Irvine’s climate, with hardware and countertop seams being the first parts to fail. Irvine’s dry summers and wet winters stress laminate and hinge plates more than a stable climate would.
Can the part be repaired instead of replaced? Often yes. Hinges, glides, and drawer boxes are usually repairable or replaceable on their own. A delaminated countertop or a swollen cabinet core usually means replacement, not repair. Call (888) 578-4462 for a free estimate to know which applies.
How long does the swap take? Hardware and drawer-box swaps usually finish in a single visit. A door or countertop replacement runs longer depending on lead time on the matched part. We give you a written timeline before work starts.
How do you source the part? We match the replacement to your CGI model line using the cabinet label and measurements, then source an OEM-compatible or quality aftermarket part. We don’t claim to carry stock – the right part is ordered to your spec. Call (888) 578-4462 to get started.
Whether you’re in Irvine and need a single hinge fixed or a full kitchen brought back to working order, we’re ready. Groundwork Construction Co. of Irvine is an independent contractor, not affiliated with CGI. Our technicians have up to 12 years of experience, every crew is background-checked and uniformed, and calls are answered by a live person 24/7. Ask about our standing offers: $1,000 off projects over $10,000, a free project estimate and design consult, and 0% financing for 18 months. Call (888) 578-4462 to schedule your free estimate.
Written by the team at Groundwork Construction Co. of Irvine, serving Irvine and nearby areas.