Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Windows & Doors: The Irvine Owner’s Guide
We install CWS-compatible windows and doors for Irvine homeowners, and the most common projects land between $4,500 – $15,000 for standard window replacement and $8,000 – $25,000 for impact-rated units, depending on count, sizing, and glass package. A failed CWS window or door usually announces itself before it breaks: the frame sticks in summer heat, water stains appear on the drywall under a corner, or the glass fogs from the inside and won’t clear.
What makes these calls tricky is that CWS built windows, doors, and component systems across a wide span of model runs and sub-series. A part pulled from a “CWS window” that came out of a different era often won’t fit, and homeowners who’ve tried it end up returning the part and calling us anyway. We’re an independent service provider, not affiliated with CWS, so we match parts to your actual unit rather than to a label that may only be half-right. Our technicians have up to 12 years of experience identifying what’s installed and what’s compatible before a single part is ordered.
Which CWS Models This Applies To
CWS isn’t one uniform product line, and that’s the first thing to understand before you order anything. The company’s window systems range from early aluminum single-hungs and sliders to later vinyl framed series with different sill and weatherstrip profiles, plus a run of impact-rated units built to Florida product approval standards (the NOA and FL approval numbers are the giveaway on those). Door lines follow the same pattern: patio sliders, hinged exterior doors, and a few specialty sash runs that used proprietary roller and latch hardware you can’t swap for a generic part.
The reliable way to identify your unit is on the label. CWS windows typically carry an etched or printed manufacturer label in one of two spots: the top of the glass at the upper corner of the sash, or the exposed face of the jamb once you lift the screen. That label gives you a series code and a date code, which together tell us which hardware and glazing configuration will actually fit. If the label is gone, we measure the sash opening, glass thickness, hardware pivot points, and sill offset. That measurement set is what separates a correct part order from an expensive mistake.
On the OEM-versus-aftermarket question, the honest answer depends on what’s failed. For rollers, latches, screen frames, and weatherstrip, a quality aftermarket equivalent from a reputable hardware supplier often performs identically and costs less. For glazed units (the glass-and-seal assembly inside the opening) and for tilt-sash hardware on newer CWS vinyl series, the correct approach is a matched or custom-built replacement, because a generic part either won’t seat or will bind within a season.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CWS Windows & Doors Is Failing
- Sticking sashes or a door that won’t latch flush. This usually points to sill and frame expansion in Irvine’s inland heat, or to a worn roller and pivot assembly on a slider. Vinyl frames expand measurably in summer and contract in winter; when that movement is combined with worn hardware, the unit stops operating smoothly.
- Fogging between the panes. A sealed unit that fogs from the inside has a failed primary or secondary edge seal, not a cleaning problem. The desiccant in the spacer is saturated and the assembly needs replacement, not a glass polish.
- Water staining or a soft spot at the interior drywall under a corner. Failed perimeter sealant, a compromised sill pan, or deteriorated weatherstrip lets water past the frame. Left alone, this is the condition that turns a window job into a wall-repair job.
- Whistling or drafts at the frame and around the latch. Worn or compressed weatherstrip and loose lock hardware are the usual culprits. On CWS sliders and hinged doors, the latch or keeper alignment is often the first thing that fails.
- Condensation on the interior glass in dry weather. That’s a sign the thermal performance of the assembly has degraded, often after years of sun exposure in a south- or west-facing opening. It’s the earliest warning that the unit is nearing replace-time.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For CWS-compatible window and door work in Irvine, plan on these ranges. The number you see is the number you pay, and it’s backed in writing.
- Window replacement: $4,500 – $15,000
- Impact-rated window installation: $8,000 – $25,000
What drives the range is straightforward: how many openings you’re doing, the size and type, glass package (standard double-pane versus low-E, laminated, or impact-rated), frame condition, and whether the opening needs new interior or exterior trim. Where glazed units or hardware are being replaced rather than whole windows, the cost sits at the lower end; full window replacement with impact glass and trim rebuilds the opening moves toward the top. Groundwork Construction Co. of Irvine provides no-hassle upfront pricing with written line-item quotes, pulls the permits, and passes inspections. All work is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. We’re an independent provider, so the guarantee is ours, and it’s in writing.
DIY or Call Us?
You can safely check a lot yourself: pull the label, note the series and date code, measure the sash opening and glass thickness, test the latch, inspect the weatherstrip, and photograph the interior staining. That’s the information we need to quote accurately. What we’d steer you away from is the removal and installation work, especially on any unit with a compromised seal at a height, or on exterior doors where a poor water-seal causes interior damage you’ll pay for later.
Window and door work is a water-intrusion problem more than a parts problem. When a sill pan, flashing detail, or perimeter seal is done wrong, the leak shows up months later and sometimes inside a wall. There’s no spring-tension or gas-line hazard here, but there IS real risk of opening a leak that costs thousands. When what you’re dealing with is failing hardware or a sealed glazed unit rather than a full window, the smart move is a quick call. Our team answers live 24/7, and we’ll tell you honestly whether it’s a sit-tight, repair, or replace situation. Call (888) 578-4462 for a free estimate on the right path.
FAQs
In this climate, most CWS windows run 20 to 30 years before the glazed unit or the sealing system needs attention, and hardware like rollers and latches typically wears out sooner, in the 8 to 15 year range depending on use. West- and south-facing units in Irvine take more sun load, so their seals and glazing tend to fail earlier than north-facing ones.
Often, yes: rollers, latches, weatherstrip, and screen frames can usually be replaced without touching the whole window or door. Failed glazed units and heavily worn tilt-sash hardware are the two cases where we recommend replacing the assembly rather than repairing the hardware, because repairing a compromised seal is a short-lived fix. We’ll check repair first before we quote replacement.
Most single-window hardware or glazed-unit swaps are completed in a single visit, and hardware-only work on a CWS slider or hinged door is quick. Whole-window replacement and impact installations take longer, and we’ll give you a realistic schedule in the written quote.
We match to your actual unit, not to a guess: the label series code, the date code, and the measured sash dimensions tell us what fits. From there we use either a matched component or a custom-built glazed unit to spec, depending on which is the correct approach for your CWS model. Because we don’t claim to carry CWS parts in stock, we order the part to the unit, which is why the label and measurements matter.
Written by the team at Groundwork Construction Co. of Irvine, serving Irvine and nearby areas.
If your CWS windows or doors in Irvine are sticking, fogging, or leaking, don’t guess at the part. Call Groundwork Construction Co. of Irvine at (888) 578-4462 to schedule your free estimate. Our team answers live, 24/7, our technicians are background-checked and uniformed, and we stand behind every job with the 730-Day Done Right Promise. We also help homeowners with KraftMaid, Cambria, and Silestone projects, and every job starts with upfront pricing and no surprises. Finishing with the right part in the first pass is the case for calling us before you order anything online.