Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Irvine Homeowners Choose Mr-Glass Construction
We provide independent Mr-Glass construction service in Irvine, CA, with a focus on frameless glass shower enclosures, walk-in showers, and tub-to-shower conversions. What makes our Mr-Glass work different is the level of specificity: we know the hinge tolerances, glass thicknesses, and sealing requirements these systems call for, and our independence means we can recommend the right fix without a manufacturer’s sales agenda pushing us toward a full replacement. We’re not affiliated with or authorized by Mr-Glass; we’re an independent service provider that works on their products every week. Call (888) 578-4462 to schedule a free estimate.
Why Trust Groundwork Construction Co. of Irvine for Your Mr-Glass Construction?
Our technicians have up to 12 years of experience, and a good share of that has been spent on Mr-Glass shower systems specifically. That matters because the details that fail are rarely obvious. A 3/8″ frameless door hangs differently than a 1/2″ panel. Hinge tolerances shift as a wall jamb settles. Bottom sweeps wear at a rate that depends on the tile curb height and how much the door gets used. We’ve worked through those variables enough times to diagnose them from the symptoms rather than by trial and error.
We source OEM-grade hinges, seals, and handles for Mr-Glass enclosures so fit and warranty validity stay intact. When an OEM panel is discontinued or priced in a way that doesn’t make sense, we’ll tell you and lay out a quality aftermarket option with the same tempered glass specs. Warranty-safe practice here means documenting what we replaced, matching original hardware where it counts, and not mixing parts in a way that gives a manufacturer an excuse to deny a claim. Every Mr-Glass job is backed by our 730-Day Done Right Promise: if it’s not done right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Mr-Glass Construction Problems We Fix in Irvine
These are the issues we run into most often with Mr-Glass products in Irvine homes, and why each one happens.
- Hinge sag on frameless doors. A frameless Mr-Glass door carrying a 1/2″ glass panel is heavy, and the hinge bushings wear over time or the wall jamb shifts slightly. The door drops, the glass edge makes contact with the wall, and you get chipping or a door that won’t close flush. This is the most common complaint we hear.
- Bottom sweep seal failure. The clear vinyl or rubber sweep along the bottom of the door is the first line of defense against water on the curb. In Irvine’s dry heat, that material hardens and cracks faster than homeowners expect, and once it fails, water migrates onto the curb and eventually into the subfloor.
- Tempered glass edge chipping. Tempered glass is strong across its face but vulnerable at the edges. Improper cleaning tools, a dropped bottle, or a door that’s been hitting the wall can chip an edge. Once the edge is compromised, the panel can’t be safely repaired and needs full replacement.
- Corroded or loosened mounting hardware. Irvine bathrooms run humid, and the hardware on a Mr-Glass enclosure takes a beating. Screws back out of tile, brackets corrode, and handles loosen. Left alone, a loose bracket puts stress on the glass and accelerates everything else.
- Improper sealing at the wall and curb. A lot of Mr-Glass installation problems trace back to the original install rather than the product. Silicone applied over a dirty or damp joint fails early, and sealing that doesn’t account for the specific tile or stone surface will let water behind the enclosure.
Mr-Glass Parts & Our Repair-vs-Replace Approach
Parts choice drives how long a repair lasts. For Mr-Glass enclosures, we use OEM-grade hinges, seals, and handles whenever they’re available, because matching the original fit keeps the door aligned and keeps warranty validity intact. When an OEM panel or part is discontinued or priced past what makes sense, we source high-quality aftermarket tempered glass built to the same thickness and safety specs and explain exactly what you’re getting.
We don’t carry stock, so every part is ordered for your specific enclosure after we’ve measured it. That’s slower than grabbing a generic hinge off a shelf, and it’s why the repair holds.
On repair versus replace, we’re honest. If the glass and frame are structurally sound and the problem is hardware or seals, repair is usually the right call and far less expensive. If the glass is chipped at an edge or the frame is compromised, replacement is more cost-effective than a repair that won’t last, and we’ll say so plainly. Call (888) 578-4462 for a free estimate and a straight answer.
Our Mr-Glass Service Process – Step by Step
- 1
Diagnosis. We check hinge alignment and bushing wear, inspect the full glass edge for chips, test the door swing, and look at the bottom sweep and wall seals. On a Mr-Glass frameless unit, we measure the door-to-wall gap to see how far the panel has sagged.
- 2
Repair or install. For repairs, we realign hinges, replace bushings and seals, and re-seal at the wall and curb using materials matched to your tile or stone. For a new Mr-Glass enclosure or conversion, we template the opening so the glass is cut to your actual walls, not a nominal size.
- 3
Test. We run water across the enclosure, check for leaks at the curb and wall joints, confirm the door closes flush with even clearance on both sides, and make sure the sweep sits correctly against the curb.
- 4
Warranty. Every Mr-Glass job is covered by our 730-Day Done Right Promise, and we document the parts we used so any future claim is straightforward.
See the difference
Before
After
Before
After
Before
AfterMr-Glass Products We Service & Install in Irvine
We work on the full range of Mr-Glass shower and glass products found in Irvine homes:
- Mr-Glass Frameless Shower Enclosures in both 3/8″ and 1/2″ glass, including hinge and seal service and full replacement.
- Mr-Glass Semi-Frameless Shower Doors, where frame-to-glass seals and pivot hardware tend to need attention.
- Mr-Glass Sliding Shower Doors, including roller and track service and re-sealing.
- Mr-Glass Custom Glass Shelving & Mirrors, from hardware replacement to new installation.
Our walk-in shower installation and tub-to-shower conversion work frequently involves a Mr-Glass enclosure as the finishing piece.
We Also Service These Brands
Mr-Glass is one brand in a much larger picture. We work across KraftMaid cabinetry, Cambria and Silestone countertops, and Kohler fixtures, so if your project touches the bathroom or kitchen beyond the shower, you’re not juggling three contractors. One team, one point of accountability, from foundation to finish line.
FAQs – Mr-Glass Construction Service in Irvine
No. We are an independent Mr-Glass service provider and are not affiliated with or authorized by Mr-Glass. We service and install their products based on our own experience with them, and we tell you that upfront so there’s no confusion about warranty administration.
Yes, we source OEM-grade hinges, seals, and handles for Mr-Glass enclosures whenever they’re available, because matching original fit keeps the door aligned and protects warranty validity. When a part is discontinued or priced unreasonably, we’ll offer a quality aftermarket alternative and explain the trade-off. Call (888) 578-4462 to talk through your specific enclosure.
Most hardware and seal repairs are completed in a single visit once the parts are in hand, while a full enclosure replacement or tub-to-shower conversion takes longer because we template the glass and order it to your opening. We’ll give you a written timeline with your estimate. Call (888) 578-4462 to schedule.
We cover Mr-Glass Frameless Shower Enclosures in 3/8″ and 1/2″ glass, Semi-Frameless Shower Doors, Sliding Shower Doors, and Custom Glass Shelving & Mirrors. If you’re unsure which you have, send us a photo and we’ll identify it.
Not when the work is done correctly. We use OEM-grade parts where they matter, document what we replaced, and avoid mixing hardware in a way that would give a manufacturer grounds to deny a claim. We’re independent, so confirm the specifics of your Mr-Glass warranty with the manufacturer, and we’ll work within it.
Here’s how our common Mr-Glass projects price out in Irvine. These are ranges; your written quote will reflect the actual opening and glass spec.
| Service | Price Range in Irvine |
|---|---|
| Walk-In Shower Installation | $4,500 – $12,000 |
| Tub-to-Shower Conversion | $3,500 – $10,000 |
| Shower Replacement | $3,000 – $8,500 |
Smaller hardware repairs (hinges, sweeps, seals) come in well below these numbers. Call (888) 578-4462 for an exact quote; estimates are free.
Book Your Mr-Glass Service in Irvine, CA
Whether your Mr-Glass frameless door is sagging, your seal has failed, or you’re planning a tub-to-shower conversion with a new Mr-Glass enclosure, we’ll give you a written, itemized estimate with upfront pricing and no surprises. Calls are answered by a live person 24/7. Call (888) 578-4462 to schedule your free estimate in Irvine.
Written by the team at Groundwork Construction Co. of Irvine.