Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Owens Corning Kitchen Remodeling: The Irvine Owner’s Guide
Owens Corning kitchen remodeling products installed by Groundwork Construction Co. of Irvine typically run $14,000 – $45,000 for a full project, with small kitchens landing around $9,000 – $20,000. We work with homeowners across Irvine on insulation, drywall, and moisture-barrier systems tied to Owens Corning specifications, and we don’t rush scheduled remodels. Most owners discover a failing component through recurring moisture near sink walls, sagging drywall seams behind base cabinets, or insulation that’s gone flat after years of Irvine’s dry heat and occasional humidity spikes.
Owens Corning is best known for fiberglass insulation, foam sheathing, and moisture-resistant drywall systems. In a kitchen remodel, these products sit behind the finishes, which means a failure shows up as a symptom, not a part swap. Staples hold up. Paper facing delaminates. Foam board shrinks at seams. That’s why diagnosis has to come before pricing.
Key Takeaways:
- Full Irvine kitchen remodels with Owens Corning systems: $14,000 – $45,000
- Small kitchen projects: $9,000 – $20,000
- We’re an independent contractor, not affiliated with Owens Corning
- 730-Day Done Right Promise backs every job
- Upfront pricing, no surprises: the number you see is the number you pay
Which Owens Corning Models This Applies To
Owens Corning doesn’t make a single “kitchen remodel” product. What they make is a family of building envelope and interior materials used in kitchens: Thermafiber mineral wool (fire and sound), R-13 and R-15 fiberglass batt insulation for interior 2×4 walls, FOAMULAR extruded polystyrene (XPS) rigid board, and the QuietZone acoustical batt line. If your kitchen project specifies any of these, that’s where compatibility matters.
Identify what’s actually behind your wall before assuming the part. Pull the electrical cover plate on an interior kitchen wall and look for the product wrap: Owens Corning batts are labeled with the R-value, the plant code, and a “PINK” or “Owens Corning” logo printed on the kraft facing. FOAMULAR board is pink or blue with “FOAMULAR” stamped directly on the surface. QuietZone batts carry a distinct “QuietZone” label, and the R-value is printed in large type – if the label is gone, a 3.5-inch batt is almost certainly R-13 or R-15, while 5.5-inch could be R-19 or R-21.
When a spec calls for Owens Corning specifically, aftermarket R-13 from another brand is not automatically interchangeable. Owens Corning’s faced batts use a specific kraft vapor retarder, and if the original spec calls for it (common on exterior kitchen walls in Irvine where the west-facing afternoon sun bakes the wall cavity), substituting an unfaced or foil-faced aftermarket batt changes the moisture management of the assembly. On interior walls, the substitution is usually fine. On exterior walls, it isn’t always.
We don’t stock Owens Corning parts or carry them on a truck. Sourcing runs through authorized distributors with a 1 – 3 day lead time on standard batt sizes.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Owens Corning Kitchen Remodeling Is Failing
Fiberglass insulation, XPS board, and acoustical batts don’t fail like a refrigerator. They fail by inches – settling, compressing, delaminating. Here’s what Irvine owners notice first.
- Sagging drywall behind base cabinets and backsplash. This usually means the kraft facing on the insulation got wet during a plumbing leak or from exterior wall vapor drive, and the paper rotted. Owens Corning faced batts are meant to stay dry; once wet, the paper breaks down and the batt loses its structure.
- Kitchen feels warmer on the west-facing wall in summer. In Irvine, west-facing kitchen walls take 6 – 8 hours of direct afternoon sun in July and August. Compressed or settled insulation (R-13 dropped to an effective R-9) shows up as a hot wall you can feel with your hand.
- Sound transfer from the kitchen to the adjacent bedroom or living room. QuietZone batts fail by compressing at the stud cavity edges – if the installer didn’t friction-fit tightly, gaps at the top and bottom plates leak sound like a screen door.
- Pink or blue foam board visible at seams with gaps. FOAMULAR XPS board is meant to fit tight. If the seams show daylight or a visible gap of 1/8 inch or more, air infiltration is real and Irvine’s coastal fog in the mornings finds it.
- Visible moisture staining or mold at wall bases behind the dishwasher or under the sink. Wet insulation is a moisture source. Once fiberglass is saturated, it doesn’t dry out in a wall cavity – it stays wet and feeds mold.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Full kitchen remodel projects with Owens Corning systems in Irvine run $14,000 – $45,000. A small kitchen remodel runs $9,000 – $20,000. Cabinet installation is $4,000 – $13,000, countertop installation is $2,000 – $6,500, backsplash installation is $800 – $2,500, and a kitchen island runs $3,000 – $10,000.
Where the range lands depends on three things: how much of the existing wall assembly you tear out (opening a wall to replace insulation means drywall replacement and patching), whether the failure is confined to one wall or extends into the ceiling cavity, and how much finish work the replacement requires. Replacing kitchen wall insulation and drywall on one wall in Irvine runs the lower end. Full perimeter re-insulation with new drywall and finish runs the upper end.
What’s included in our quote, line by line: material (Owens Corning spec, or approved equivalent), removal of failing material, install, drywall patch and finish, prime and paint touch-up, and cleanup. Permits pulled where Irvine requires them, inspection passed. The 730-Day Done Right Promise covers the workmanship, and if it’s not done right, we make it right. Upfront pricing, no surprises – the number you see is the number you pay.
| Line Item | Irvine Installed Range |
|---|---|
| Full kitchen remodel (Owens Corning systems) | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island | $3,000 – $10,000 |
Financing available: 0% for 18 months, and $1,000 off projects over $10,000.
DIY or Call Us?
What a homeowner can safely check: the label behind an electrical cover plate, the visible seam gaps on foam board after pulling a cabinet drawer, and whether the drywall behind the backsplash shows water staining. For Irvine kitchens, that’s often enough to confirm whether the problem is insulation or plumbing.
Where DIY goes wrong: opening a wall cavity yourself. Removing drywall to replace insulation is not a simple swap. You’re opening the building envelope, dealing with existing wiring, potentially disturbing plumbing, and if you don’t reinstall the vapor retarder correctly, you create a worse moisture problem than the one you’re fixing. Drywall and finish work that looks bad is one thing; a wall assembly that traps moisture and grows mold is another. This is a job where the cost of getting it wrong is significantly higher than the cost of having it done right.
Our technicians have up to 12 years of experience on building-envelope and finish work. Call (888) 578-4462 – live person, 24/7 – to schedule your free estimate.
FAQs
Owens Corning fiberglass batt insulation lasts as long as it stays dry and uncompressed – often 30+ years in a stable wall cavity. In Irvine, the failure mode isn’t age, it’s moisture from plumbing leaks or exterior wall vapor drive, plus compression from poorly fit batts. If it’s dry and fully lofted, it’s fine. If you can see stained paper facing or notice a hot west wall, it’s time for a look.
Call (888) 578-4462 for an exact quote – estimates are free.
Sometimes. A small localized gap at a stud bay or a single wet batt can often be repaired by removing and refitting the material. Once the kraft facing has delaminated or the batt has compressed permanently, replacement is the only fix that restores the R-value. FOAMULAR board with a visible seam gap can sometimes be sealed with spray foam and taped; board that’s shrunk at the edges usually needs replacement. Diagnosis decides.
Call (888) 578-4462 and we’ll walk through what you’re seeing.
One wall of insulation and drywall replacement in a kitchen is typically a 2 – 4 day job once the wall is opened. A full perimeter re-insulation with drywall and finish runs 5 – 10 days. We schedule the tear-out, the install, and the finish work as one job with one crew, no change orders unless you add scope.
Call (888) 578-4462 for a written timeline tailored to your kitchen.
We source through authorized Owens Corning distributors with a 1 – 3 day lead time on standard batt sizes and FOAMULAR board. We don’t stock parts or carry them on a truck; your material arrives matched to the spec for your kitchen. If the original spec calls for an Owens Corning-specific product that’s discontinued, we identify the current equivalent and get your written approval before ordering.
Call (888) 578-4462 for a free estimate with a line-item material list.
Ready to price your Irvine kitchen remodel? Call (888) 578-4462 for a free estimate and design consult – live person, 24/7, no voicemail. Every project is backed by the 730-Day Done Right Promise, background-checked uniformed technicians, and upfront pricing with no surprises. We also work with KraftMaid, Cambria, and Silestone when your kitchen calls for cabinetry and countertop upgrades alongside the Owens Corning systems.
Written by the team at Groundwork Construction Co. of Irvine, serving Irvine and nearby areas.