A Groundwork company - serving Irvine, CA

PGT Fence Installation in Irvine, CA

FenceFence
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

PGT Fence Installation: The Irvine Owner’s Guide

PGT fence installation in Irvine typically runs $3,500 to $9,000 installed, depending on gate count, height, and how much site prep the yard needs. We install and repair PGT-compatible fence systems for Irvine homeowners and can usually get a failed gate, post, or latch section back in working order in a single visit. Most owners only discover something’s wrong when a gate starts dragging on the ground, a latch stops catching, or a post shifts after a wet winter and the whole run starts to lean.

Call (888) 578-4462

PGT is best known for windows and doors, and that’s worth stating plainly up front: we’re an independent service provider, not affiliated with PGT. But we work on PGT-branded and PGT-compatible exterior products often enough to know the specs, the common failure points, and where a homeowner can get talked into the wrong replacement part. If your fence hardware or gate assembly carries a PGT label or came with a PGT-spec package, this page is for you.

Which PGT Models This Applies To

PGT exterior products are tied to model and series numbers, and the part you need is tied to that number in turn. The label is typically on the gate frame, the hinge plate, or the post bracket. If the label is weathered off, measure the hardware footprint instead: hinge spacing, post width, and gate frame thickness are the three numbers that will match you to the right assembly.

Here’s the compatibility gotcha most Irvine homeowners miss. PGT fence and gate hardware is often matched to a specific frame thickness and latch throw depth, and a generic hardware set from a big-box store will usually bolt on but won’t align properly. You’ll get a gate that closes but doesn’t latch flush, or a hinge that wears out in a season because the load isn’t distributed the way the PGT frame was designed for.

OEM or aftermarket for a PGT system?

For gate hardware, latches, and hinges, we favor OEM or true OEM-equivalent parts when they’re available, because the dimensional tolerances matter more than most homeowners realize. For panels, posts, and rails, a quality aftermarket equivalent is often the smarter spend, especially on a fence that’s already north of ten years old. We’ll tell you which is which before you commit to anything, and our pricing is upfront with no surprises.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your PGT Fence Installation Is Failing

  • Gate dragging on the ground or scraping the driveway. Usually a sagging hinge or a post that’s settled on one side. Irvine’s expansive clay soils shift seasonally, and a post set without proper depth or base material will move within a few years.
  • Latch not catching or popping open on its own. The latch throw has worn past the strike plate tolerance. This is a security issue, not just an annoyance, and it’s usually a small part swap rather than a full gate replacement.
  • Loose or wobbly posts after rain. Water pooling at the post base rots the footing or undermines the concrete collar. If a post moves by hand, the footing needs attention before the panels above it fail.
  • Rust streaks or white corrosion on hardware. Salt air and coastal humidity work on cheap fasteners faster than most people expect. Visible corrosion on hinges or brackets means the hardware is past its service life, even if the panels look fine.
  • Panels leaning out of plumb. A run that was square last year and leans this year is telling you the soil or the footings are the problem. Catching this early saves the panel replacement that follows.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

For Irvine, expect $3,500 to $9,000 for a full vinyl fence installation, and $4,000 to $10,000 for aluminum. Hardware-only repairs (a hinge set, a latch assembly, a single post reset) land well below that and we’ll quote them separately so you’re not paying for a full install when a part swap will do. The range is driven by linear footage, gate count, height, material choice, and site prep – a yard with root intrusion or a failed existing footing costs more to set right than a clean run.

What’s included in the quote

  • Written line-item quote with parts and labor separated
  • Removal and haul-away of the failed section or hardware
  • Post footing repair where needed
  • Cleanup and a final walkthrough before we call it done

Every fence project we complete is covered by our 730-Day Done Right Promise. If it’s not done right, we make it right. We also offer 0% financing for 18 months and $1,000 off projects over $10,000, so a larger run or a full replacement doesn’t have to come out of savings in one hit.

DIY or Call Us?

Some of this you can safely check yourself. Walk the fence line and look for movement at the post base, test the latch by hand, and look for rust or corrosion on the hardware. Those are five-minute checks that tell you whether you’re looking at a part swap or a footing problem.

Where DIY goes wrong is at the footing and the gate frame. Digging out and re-setting a post without knowing the soil conditions or the correct base depth is how a one-weekend job turns into a leaning run by the next rainy season. Adjusting a gate hinge on a PGT frame without matching the load spec is how you get a gate that latches for three months and then doesn’t. And if the hardware is load-bearing or the post is structural, a bad DIY fix can turn a safe gate into one that swings open onto the driveway. Call us at (888) 578-4462 and we’ll tell you honestly whether it’s a part swap or a bigger job.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 578-4462
Local Service Coverage

Request a Free Estimate in Irvine

Tell us what you need - Groundwork Construction Co. of Irvine responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch