Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Driveway & Pavers: The Irvine Owner’s Guide
Schluter-compatible paver and driveway assemblies in Irvine typically run $7,000 – $18,000 installed for a full paver driveway, and smaller repairs or partial resets usually land in the $600 – $2,500 range depending on what failed. We’re an independent contractor and not affiliated with Schluter, so we match the right components to your system rather than pushing a single proprietary part.
Most Irvine owners find out something’s wrong the same way: a paver edge starts rocking underfoot near the garage apron, or the joint sand washes out after the first big rain and won’t stay put. The pattern shows up on the driveway first, then at the patio transition, then along any slope draining toward the street. Our technicians have up to 12 years of experience with these layouts, and this guide covers what actually fails, what replacement costs, and when to call us at (888) 578-4462.
Which Schluter Models This Applies To
Schluter’s paver and driveway line covers a few distinct component families, and matching the right one matters more than most homeowners expect. The DITRA and DITRA-HEAT membranes are for tile and stone; the exterior paver work you’re looking at is typically built around the TROBA drainage system or the paver edge profiles in the TREP line. If your assembly includes a linear drain under the pavers, that’s a separate KERDI-DRAIN or KERDI-LINE component with its own sizing.
To identify what you have, check three things: the printed label on any leftover membrane roll or box (series name and roll dimensions are usually stamped on the core), the exposed edge at the driveway apron where the profile meets concrete, and the drain grate width if water is pooling. Schluter’s naming is dimension-based, so a 3/8-inch profile won’t swap for a 1/2-inch without reworking the paver bed.
On OEM versus aftermarket: for the drainage mats and edge profiles, genuine Schluter components are worth the cost because the sizing tolerances hold. For joint sand and polymeric fillers, a quality aftermarket product performs the same in Irvine’s climate, and we’ll tell you which is which before you spend. For kitchens and baths in the same home, we also service KraftMaid, Cambria, and Silestone products.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Driveway & Pavers Is Failing
Failures announce themselves early if you know what to watch for. Here’s what Irvine homeowners describe most often:
- Pavers rocking near the garage apron. The bedding layer has shifted or compacted unevenly, usually from water finding a path under the edge profile. In Irvine, we regularly see this on driveways draining toward the street where a shallow slope pulls moisture under the pavers instead of shedding it.
- Joint sand washing out after rain. Polymeric sand that breaks down within one or two seasons points to a drainage component that isn’t moving water where it should. When the TROBA mat clogs with silt, water backs up through the joints instead of draining away.
- Standing water at the patio or driveway transition. A blocked or undersized linear drain, or one installed at the wrong elevation. Our wet-season rain in Irvine comes in concentrated bursts, and a drain that’s off by a quarter inch will pond instead of clear.
- Edge profile lifting or separating. The fasteners or adhesive holding the profile to the concrete have failed, often because the base wasn’t stable when it was set. You’ll see a visible gap or a lip you catch a toe on.
- Efflorescence or white crust on the surface. Salts pulled up through the paver bed by moisture that can’t escape. Recurring efflorescence is a drainage symptom, not a cosmetic one.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Replacement pricing in Irvine depends on what failed and how much of the assembly needs to come up. Here’s what we typically see:
- Paver driveway installation (full): $7,000 – $18,000
- Paver patio installation: $3,500 – $11,000
- Driveway replacement (removal and rebuild): $5,000 – $14,000
- Driveway sealing: $250 – $700
- Drainage component or edge profile reset: $600 – $2,500 for a targeted repair
What drives the range: square footage, whether the base needs rebuilding versus spot repair, and whether you’re replacing the drainage mat or just the visible profile. Every quote is a written line-item breakdown so you see parts and labor separately, and the number you see is the number you pay. Our work is covered by the 730-Day Done Right Promise, and we pull the permits the work requires.
DIY or Call Us?
There’s a safe lane for a homeowner here and a lane where DIY costs more than it saves. You can safely lift a loose paver, vacuum out the joint sand, check for water staining on the base, and photograph any exposed edge profile or drain grate so you know what you’re dealing with. That inspection won’t hurt anything and it gives us a head start.
Where DIY goes wrong: rebedding pavers on a drainage system without knowing how the mat is oriented, cutting a new edge profile to the wrong dimension, or resealing over an active moisture problem and trapping it under the surface. Water that’s been misrouted for a season can undermine the entire base, and that’s a bigger bill than the original repair. If your pavers move more than a quarter inch or the drain won’t clear, call us at (888) 578-4462 and we’ll take a look.
FAQs
How long do Schluter driveway and paver assemblies last in Irvine? A properly installed paver driveway with a functioning drainage system typically holds 20 to 30 years, but the drainage mat itself can clog with silt within 8 to 12 years if the inlet isn’t kept clear. Our dry summers and concentrated winter rain are hard on drainage components. Call (888) 578-4462 for an inspection estimate.
Can my failing paver edge be repaired instead of replaced? Often, yes. A localized edge profile reset or drainage component swap runs about $600 – $2,500 and usually fixes the problem if the base is still sound. If the pavers are rocking across a wide area, the base has shifted and needs more work. We’ll tell you honestly which one you’re facing.
How long does a repair or swap take? A targeted drainage or edge repair is usually completed in a single visit, often a half day to a full day depending on access. A full paver driveway rebuild typically takes 2 to 4 days once materials are on site. Call (888) 578-4462 and we’ll scope it for your specific layout.
How do you source the part for my system? We identify the component from the label, edge profile, and drain dimensions at your property, then order the matching Schluter-compatible part before the work date. We’re an independent contractor and not affiliated with Schluter, so we source by fit and spec, not by brand loyalty. Estimates are free.
If your driveway or patio is showing any of these signs, the sooner we look, the smaller the repair. Call Groundwork Construction Co. of Irvine at (888) 578-4462 to schedule your free estimate. Calls are answered by a live person 24/7, our technicians arrive background-checked and in uniform, and every project is backed by our 730-Day Done Right Promise. No-hassle upfront pricing, 0% financing for 18 months, and $1,000 off projects over $10,000.
Written by the team at Groundwork Construction Co. of Irvine, serving Irvine and nearby areas.