Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Bathroom Remodeling: The Irvine Owner’s Guide
Bathroom remodeling built around Tamko materials in Irvine typically runs $9,000 to $28,000 installed, depending on whether you’re working with a compact hall bath or a full primary suite, and most projects are scheduled on a normal build calendar rather than treated as an emergency. The part that fails in a Tamko system is usually the moisture barrier behind tile, the sealant at a wet wall, or a shower pan liner that was never tied into the waterproofing correctly. Irvine owners tend to find out the hard way when grout starts crumbling, a baseboard swells, or a faint musty smell shows up after a shower.
Which Tamko Models This Applies To
Tamko makes several product families that turn up in Irvine bathrooms, and the right replacement depends on which one you actually have. The most common are the waterproofing membranes and underlayments used beneath tile and the roofing-grade materials some builders carried over onto exterior walls and additions. To identify your product, look for the print stamped on the face of the membrane or the label on the roll end, note the width (common roll widths run 36 inches and 39 inches), and measure the thickness with a set of calipers if you can. Thin, sheet-style membranes and thicker, fabric-reinforced versions are not interchangeable, and neither are the bonding adhesives. When we source for an Irvine project, we either match the existing Tamko product by spec or offer a verified aftermarket equivalent with the same coverage and thickness. We’re an independent contractor, not affiliated with Tamko, so we match the part to your system rather than pushing one brand line.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tamko Bathroom Remodeling Is Failing
- Crumbling or hollow grout lines. Water is getting behind the tile and the membrane underneath is no longer doing its job, often because a seam lifted or a fastener punctured it.
- Soft or swollen baseboards near the shower. Moisture is escaping the wet zone and soaking into the wood, which points to a failed seal or a pan that was never sloped correctly.
- A musty smell that lingers after showers. That’s trapped moisture, usually between the tile and the substrate, and in Irvine’s warm climate it can turn into visible mold within a season.
- Lifted or bubbled membrane at the edges. Adhesive failure or poor surface prep, common when a prior installer didn’t let the substrate cure before laying the sheet.
- Visible cracks at inside corners. Movement at the wall-floor junction has broken the seal, and corners are the first place a shower leaks.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Replacing Tamko-related bathroom waterproofing and materials in Irvine lands inside our $9,000 to $28,000 bathroom remodel range, with smaller repairs and partial retiling on the low end and full teardown-and-rebuild on the high end. A few line items to anchor your budget: shower replacement $3,000 to $8,500, walk-in shower installation $4,500 to $12,000, and tub-to-shower conversion $3,500 to $10,000. What drives the range is the extent of water damage behind the wall, whether the pan has to be rebuilt, and tile selection. Our quotes are line-item, upfront, and the number you see is the number you pay. Every job is backed by our 730-Day Done Right Promise, so if the waterproofing fails inside that window, we make it right.
DIY or Call Us?
You can safely check for a failing membrane by pulling a loose tile, pressing a screwdriver into soft drywall near the shower, or looking for water staining on the ceiling below. What you shouldn’t do yourself is cut into a shower pan or tear out waterproofing without knowing where the water line and drain assembly run, because a bad cut there can flood the room below. Waterproofing is unforgiving, and a membrane installed over a damp substrate or with the wrong adhesive will fail quietly and expensively. We’d rather you call and let us take a look. Reach us at (888) 578-4462 and a live person answers, any hour.
FAQs
A correctly installed Tamko membrane typically holds 15 to 25 years in an Irvine bathroom, though our dry inland heat and hard water speed up wear at the seals and corners well before the sheet itself gives out. Call (888) 578-4462 for a free assessment.
Sometimes yes. A single failed seam or a cracked inside corner can often be repaired without tearing out the whole shower, and we’ll tell you honestly which one your Irvine project needs. Call (888) 578-4462 for an exact quote.
A targeted waterproofing repair runs one to three days, while a full shower rebuild runs one to two weeks once materials are on site. Call (888) 578-4462 to schedule your free estimate.
We match by spec against your existing Tamko product or a verified aftermarket equivalent with the same roll width and thickness, ordered for your Irvine address. We don’t stock parts or carry them on a truck. Call (888) 578-4462 for a quote.
We also service KraftMaid, Cambria, and Silestone in Irvine bathrooms, so if your project touches cabinetry or counters, we handle the whole scope from foundation to finish line. Every technician is background-checked and arrives in uniform, and calls are answered by a live person 24/7. If your Tamko bathroom is showing signs of failure, call (888) 578-4462 for a free estimate and design consult. We offer $1,000 off projects over $10,000 and 0% financing for 18 months.
Written by the team at Groundwork Construction Co. of Irvine, serving Irvine and nearby areas.