Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Windows & Doors: The Irvine Owner’s Guide
We install Tamko-compatible windows and doors across Irvine, with full window replacement typically running $4,500 – $15,000 and impact-rated units reaching $8,000 – $25,000 depending on count, glass package, and frame material. Most Irvine jobs are scoped, permitted, and scheduled within the same working week, and every one is backed in writing by our 730-Day Done Right Promise. We’re an independent service provider, not affiliated with Tamko.
Owners rarely call us because they know the word “Tamko.” They call because a door sticks in August, a window crank strips out in October, or a fogged pane shows up between the glass after a Santa Ana wind event. Irvine sits in a dry, marine-influenced climate that swings hard between cool coastal mornings and hot inland afternoons, and that daily expansion-contraction cycle is what finishes off gaskets, sealant, and hardware long before the glass itself gives out.
Which Tamko Models This Applies To
Tamko’s window and door line has shifted over the years through acquisitions and product consolidations, which is exactly why parts matching gets tricky. Older Tamko vinyl and aluminum units often show a certification label on the frame or sash with a series designation and a manufacturing code; newer units may only carry a glass unit label. Pull the label before you measure anything. If there’s no label, measure glass width and height to the nearest 1/16 inch and measure sash thickness, then photograph the hinge, lock, or crank mechanism with a tape measure in frame. That photo is usually what shortens a parts call from twenty minutes to two.
Tamko glass units are commonly specified in 3/4-inch overall thickness, and Irvine homes built in the 1980s and 1990s frequently have 5/8-inch units instead, so a straight swap without checking that dimension will leave you with a unit that won’t seat. The OEM-versus-aftermarket call matters here: for a failed insulated glass unit, a quality aftermarket fabricator can typically match the spacer and low-E coating spec at a better number than an exact Tamko replacement, and the performance data is documented either way. For hardware (cranks, locks, rollers, glazing beads), an exact-match mechanism is usually the safer bet because mounting patterns changed between series. For full-unit replacement on a house we’re already working on, we’ll show you both paths: matching the Tamko unit or moving to Andersen or Marvin lines we carry as brand partners.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tamko Windows & Doors Is Failing
- Fogging or condensation between the panes. The seal on the insulated glass unit has failed and moisture is entering the dead air space. No amount of cleaning fixes this; the glass unit has to be replaced.
- A crank that spins freely or feels gritty. The operator mechanism has stripped gears or dried-out lubrication. Common in Irvine on west-facing windows that bake every afternoon and cool every night.
- Doors that drag, stick, or won’t latch in summer. Frame movement or a worn hinge and strike. On slider doors this is often a flattened roller rather than a frame problem, which is a much smaller repair.
- Drafts or visible daylight at the frame. Failed weatherstripping, gaskets, or perimeter sealant. This is the one that quietly shows up on your energy bill before you notice it with your hand.
- Water staining or soft trim below a sill. Water is getting behind the frame, usually past a failed seal or a missing head flashing. Left alone, this reaches the wall sheathing.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed window replacement in Irvine runs $4,500 – $15,000 for a typical whole-house replacement, and impact window installation runs $8,000 – $25,000. Single-pane glass unit swaps, hardware replacement, and door roller repairs sit below the full-replacement range and get quoted line by line.
What moves you up or down that range: the number of units, frame material (vinyl versus wood-clad aluminum), whether we’re matching into existing openings or reframing, glass package (low-E, argon, laminated, impact-rated), and second-story access with stucco detailing to restore.
The number you see is the number you pay. Our quotes itemize parts and labor separately so you can see what the glass unit costs versus the install, and permits are pulled and inspections passed on every job that requires them. Workmanship is covered by the 730-Day Done Right Promise. $1,000 off applies to projects over $10,000, and 0% financing for 18 months is available.
DIY or Call Us?
Here’s the honest split. You can safely check and do the small stuff: clean and lubricate a sticking crank, replace weatherstripping, adjust a door strike plate, tighten hinge screws, and re-caulk a perimeter joint with a proper exterior sealant. Those are afternoon tasks with a screwdriver and a caulk gun.
Where it goes wrong: pulling a fogged insulated glass unit yourself on a second story, resetting a door frame that’s out of square, or chasing a water leak to its actual source. Window and door work means working at height and behind finished walls, and a bad seal job on a $12,000 window package costs more to fix than doing it right the first time. If you’re not sure what’s failing, call (888) 578-4462 and we’ll tell you straight: repair what’s repairable, replace what isn’t. Estimates are free, and a live person answers around the clock.
FAQs
Figure 15 – 25 years for the frame and hardware, and 10 – 20 years for the insulated glass seal depending on sun exposure. Irvine’s west- and south-facing units often fail on the shorter end of that glass range because of the daily heat cycle. If your glass is fogging at 12 years, that’s not unusual here. Call (888) 578-4462 for an assessment before assuming you need full replacement.
Usually yes for hardware, rollers, hinges, weatherstripping, and cranks, which is the cheaper path and the one we’ll recommend when it holds. A fogged glass unit can also be swapped without replacing the frame in most cases. Call (888) 578-4462 with a photo of the label or mechanism and we’ll tell you which way makes sense.
A single glass unit or hardware repair is typically done in one visit. A full window replacement across an average Irvine home runs one to three days depending on unit count and stucco restoration. Finishing and paint touch-up happen at the end of the same project. Call (888) 578-4462 to schedule your free estimate and get a firm timeline in writing.
We identify your exact Tamko series from the frame label or measurements, then source the matching glass unit or mechanism through our supplier network, or bring in an equivalent aftermarket unit with documented specs when it’s the better value. We don’t stock parts or carry them on trucks; each part is ordered to your unit. Call (888) 578-4462 to start the match. We also work with KraftMaid, Cambria, and Silestone on other parts of the home.
Ready to price it? Call Groundwork Construction Co. of Irvine at (888) 578-4462 for a free estimate. A live person answers 24/7, our technicians are background-checked and arrive in uniform, and with up to 12 years of experience on our crews, we’ll get your Tamko windows and doors back to doing their job. From foundation to finish line, built to last and backed in writing.
Written by the team at Groundwork Construction Co. of Irvine, serving Irvine and nearby areas.